Stainless steel weld bung to add an O2 sensor for wide range of use. Comes with a plug so you can remove it from the car. Get one for every car so you can move your meter around. ( Click for more details )
Item Code: 001O2BUNG
6-ft. long, mini to stripped-and-tinned, matching LM-1 analog output spcifications ( Click for more details )
Item Code: 32716140
Includes an integrated circuit for converting tach or inductive clamp output to a clean analog signal that can be logged by the LM-1. The cable can be calibrated to the characteristics of your engine through a simple setup routine. **Inductive Clamp ( Click for more details )
Item Code: 3273726
***NOT FOR USE WITH NEW LM-2*** For use only with the RPM Converter (LMA-2), AuxBox (LMA-3), or the DL-32 (6ft.) ( Click for more details )
Item Code: 3273727
Patent-pending, Venturi-effect, tapped exhaust clamp for obtaining accurate lambda measurements in non-cat autos or other engines. A must if you don't have or don't want to install a bung for testing. ( Click for more details )
Item Code: 3273728
The Bosch LSU4.2 wide-band O2 sensor (shipped as part of the LM-1 kit) is rated to operate at an exhaust gas temperature of < 1300 degrees (F), and a sensor housing temperature of < 900 degrees (measured at the bung) for maximum accuracy and ... ( Click for more details )
Item Code: 3273729
Wall adapter for LM-1 meter only. ( Click for more details )
Item Code: 3273732
Adapter for computers without Serial ports. This cable will convert Serial to USB. Software included. ( Click for more details )
Item Code: 3273733
Bung & Plug Kit ( Click for more details )
Item Code: 3273736
Bosch LSU4.2 5-wire, wide-band O2 sensor ( Click for more details )
Item Code: 3273737
( Click for more details )
Item Code: 3273738
To minimize the effects of noise coupling with the extended-length sensor cable, Innovate recommends minimizing the length of the power-supply cable. <2’ is ideal. Noise coupling may be present if the bar graph is flickering. Excessive coupling will ( Click for more details )
Item Code: 3273739
Item Code: 3273740
Accessory for LM-1 Only! Not needed with LC-1. The latest model Autronic ECU does not require this cable. To better interface with Autronics’ ECUs, we’ve developed a custom interface cable. This is essentially a modified analog output ... ( Click for more details )
Item Code: 3273745
The Serial Program Cable will allow you to connect any of the following devices to your PC. (LC-1, XD-1, LMA-3) ( Click for more details )
Item Code: 3273746
Terminator Plug for use with XD-1, LMA-3, LC-1, and ST-12. ( Click for more details )
Item Code: 3273750
P/N: 3760 is also needed to connect the LM-1 to the XD-1. ( Click for more details )
Item Code: 3273759
This custom cable will allow you to connect and/or daisy chain the following products: XD-1, LC-1, LMA-3, ST-12. Also used to connect the LM-1 to the XD-1. ( Click for more details )
Item Code: 3273760
Extended Bung & Plug (1 inch) Mild Steel ( Click for more details )
Item Code: 3273764
This custom cable will allow you to connect and/or daisy chain the following products: XD-16, LC-1, LMA-3, DL-32, SSI-4, TC-4, & ST-12. Also used to connect the LM-1 to the XD-16. ( Click for more details )
Item Code: 3273789
The XD16+ kit includes the same components as an LC1+ kit, plus an XD-16 gauge.The XD-16 features programmable LED colors and a remote control button to start and stop log sessions, initiate calibrations, or view min/max values. ( Click for more details )
Item Code: 3273798
**Gauge Only** This gauge can be purchased as an accessory to be used with the LC-1 or LM-1. These kits includes the DB Gauge, mounting hardware, CD and quick-start guide. ( Click for more details )
Item Code: 3273803
Item Code: 3273804
Replacement Power Cable. Included with LM-2 kit. ( Click for more details )
Item Code: 3273808
OBD-II / CAN Interface Accessory Cable for LM-2. ( Click for more details )
Item Code: 3273809
Replacement 8ft Sensor Cable. Included in LM-2 kits. ( Click for more details )
Item Code: 3273811
LM-2 Serial Patch Cable makes the LM-2 MTS Compatible (LC-1, LMA-3, DL-32, SSI-4, TC-4). Four pin Molex to serial 2.5. *Not included with LM-2 kit* ( Click for more details )
Item Code: 3273812
Replacement USB Cable for LM-2. Included in LM-2 kits. ( Click for more details )
Item Code: 3273813
The "Window Mount" will allow you to have the LM-2 mounted to your windshield. This will help provide a better view of the display while tuning. **LM-2 pictured....not included** ( Click for more details )
Item Code: 3273814
-Inductive Clamp Accessory for LM-2, DL-32, LMA-3, and RPM Converter. -Simply clamp on to one spark plug wire to log RPM. -Cable is 6 feet in length. Kit includes: Inductive Clamp and LM-2 ... ( Click for more details )
Item Code: 3273834
This Stainless Steel adapter allows you to use a full size 18mm thread O2 Sensor in a 12mm Original Equipment bung. Most Import Motorcycles, ATV's etc. come with a 12mm O2 sensor. This adapter allows you to use one of Innovate's Data loggers or ... ( Click for more details )
Item Code: 3273835
-Carrying Case for LM-2 Digital Air/Fuel Ratio Meter (Black) -Foam insert fits LM-2 for better protection -Innovate Motorsports Logo printed on Case -Room to store all cables needed for the kit ( Click for more details )
Item Code: 3273836
(586) 294-4404
